RHS Galvanised Steel
Front Stable Panel 4m Ply Mesh Combo Half Gate
4 m front stable panel with ply lower, galvanised mesh upper and a 1500 × 1200 mm half gate. It closes the front of a standard 4 m × 4 m bay or a large bay with a 4 m front, in a new stable run or a shed retrofit.
The panel and gate are each welded as a single piece from 50 × 50 mm galvanised RHS in our Yatala, QLD workshop. Mesh above the 17 mm form ply keeps air moving through the front of the bay, and the gate closes with a recessed slam latch. The panel joins to side and divider panels with cattle drop pins and sleeves.
- Panel length: 4 m
- Height: 2.4 m
- Suits: 4 m front bays (Standard 4 × 4 m, Large 4 m front)
- Infill: 17 mm form ply lower, 4 mm galvanised mesh upper
- Gate: 1500 × 1200 mm half-height straight swing gate, recessed slam latch
- Frame: 50 × 50 mm galvanised RHS, welded panel
$1,540.00
4m Ply/Mesh Front Panel with Half Gate
Guerilla Steel 4m Ply/Mesh Front Panel – Half Gate Included, Suits Retrofit Builds
Stable Panel Specs
17mm form ply · 4mm galvanised mesh
1500mm W x 1200mm H Straight Gate with recessed slam latch
Options
What Guerilla Steel Stable Owners Say
Building Buying & Owning - Stable Panel
Stable Panel FAQs
Our fully welded panels connect using heavy-duty cattle drop pins. The connection points line up and the pins drop into place. The pin sleeve joint make assembly straightforward and allows panels to be reconfigured or additional bays added later.
Standard panel frames measure 4000mm long × 2400mm high × 50mm thick. A standard 4m × 4m stable provides 16m² of internal floor space, with an outside frame measurement of 4100mm × 4100mm.
Each adjoining bay shares a dividing panel and adds 4050mm to the overall length: 4000mm for the additional front panel, plus 50mm for the next end or dividing panel.
| Configuration | Outside frame dimensions | Internal floor area |
|---|---|---|
| Single bay | 4100mm × 4100mm | 16m² |
| Two adjoining bays | 8150mm × 4100mm | 32m² |
| Three adjoining bays | 12,200mm × 4100mm | 48m² |
These are frame dimensions. Roof overhangs extend beyond this footprint and need to be allowed for when planning your site.
The Guerilla Steel range works as one modular system. You can add bays, tack rooms or wash areas anytime without rebuilding the original stable. Front/rear and end/dividing panels are interchangeable across our stables and shelters, making it easy to reconfigure your layout or add more bays later.
If you’re likely to expand, plan the orientation, access and available space from the start.
End and dividing panels use double pin sleeves. Front gate and rear panels use matching single pin sleeves. These line up so the connecting pins can drop into place.
When ordering panels individually, select the correct sleeve configuration for where the panel will sit. If you’re adding to an existing stable, send us a photo of the connection points so we can confirm the match before you order.
No welding or advanced building skills are needed. Each front side and dividing panel arrives fully welded. They connect together with pin and sleeve joints. You’ll need to keep panels square and level, and securely anchor the frame. Have another person help position and hold panels. See the DIY Stable Guide
Have these tools ready:
- Cordless drill or impact driver
- Socket and spanner set
- Spirit level and tape measure
- Rotary hammer drill if anchoring into concrete
- Ladder, clamps and appropriate safety gear
Info For Customers

Planning your Horse stable? Get the Stable Building Site Prep Checklist

Horse Stable Design Planning Guide: Best Sizes, Setup Tips, Planning Advice

Building Your Own Horse Stable? DIY Flat Pack Kit’s are Easier Than You Think.

Steel Horse Stable Maintenance, A Practical Guide for Long-Term Strength and Safety
Upgrade & Customise
Configure with different modular addons, and upgrades available. Change mesh tops, swap form ply panels, upgrade gates, or roofing options. Add a tack room, wash bay or day yard. See the full range for all options.

Guerilla Steel Ground Anchor Kit – 4x Anchors Per Bay, Suits Ground/Gravel/Grass Set for 1 Bay

Guerilla Steel Yoke Gate upgrade provides a higher barrier with head-out access for younger, high-energy horses or stallions prone to testing stable gates

Guerilla Steel 4m Front Roof Pitch Frame – Per Bay, Improved Fall, Drainage & Airflow (Includes Set of 2x 2000mm x 250mm h Panels per bay)
More Options
Not sure if this one's right for you?
Tell us 3 things and we'll come back with a recommendation. No quote yet — just an honest opinion from someone who builds these every day.
or just call · 0405 538 413Ready to Order Your 4m Front Panel?
$1,540.00






